Anaerobic High-temperature Test Chamber
● Independent air circulating cooling device.
● Door seal strip with unique thermal insulation function.
● 2 sets of baffles with the maximum loading capacity of 45Kg.
● Self-diagnosis function alarm is used to identify and assist in solving the problem.
● Unique 3-layer chamber structure allows to cool down quickly.
● Unique pneumatic design ensures rapid cooling to reduce concentration and keep low oxygen concentration.
- specifications
- Refrigeration system
- Control system
- configuration
- accessories
型号Model | AT91-200 | AT216-200 | AT512-200 | AT1000-200 | AT91-300 | AT216-300 | AT512-300 | AT1000-300 | ||
内容积(L)Internal Volume (L) | 91 | 216 | 512 | 1000 | 91 | 216 | 512 | 1000 | ||
内箱尺寸(mm) Inner Dimension (mm) | W | 450 | 600 | 800 | 1000 | 450 | 600 | 800 | 1000 | |
H | 450 | 600 | 800 | 1000 | 450 | 600 | 800 | 1000 | ||
D | 450 | 600 | 800 | 1000 | 450 | 600 | 800 | 1000 | ||
外箱尺寸(mm) Outer Dimension (mm) | W | 1060 | 1210 | 1500 | 1730 | 1060 | 1210 | 1500 | 1730 | |
H | 820 | 970 | 1210 | 1480 | 820 | 970 | 1210 | 1480 | ||
D | 635 | 785 | 1065 | 1270 | 635 | 785 | 1065 | 1270 | ||
温度范围(℃)Temperature Range (℃) | (环温+20~200)℃ (Ambient temperature +20~200)℃ | (环温+20~300)℃ (Ambient temperature +20~300)℃ | ||||||||
升温时间(min) Temperature Rise and Time(min) | (环温+20~200)℃ (Ambient temperature +20~200)℃ | (环温+20~300)℃ (Ambient temperature +20~300)℃ | ||||||||
≤40/min | ≤60/min | ≤70/min | ||||||||
箱内残留氧气浓度≤100ppm,耗高纯度惰性气体(如:N2)流量 Residual oxygen concentration ≤100ppm, consumption flow of high-purity inert gas (such as: N2) | ≤20L/min (≤50min fall ) | ≤50L/min (≤50min fall ) | ≤100L/min (≤50min fall ) | ≤200L/min (≤50min fall ) | ||||||
≤7L/min(浓度保持) ≤7L/min (concentration maintaining) | ≤15L/min(浓度保持) ≤15L/min (concentration maintaining) | ≤30L/min(浓度保持) ≤30L/min (concentration maintaining) | ≤60L/min(浓度保持) ≤60L/min (concentration maintaining) | |||||||
调温方式 Temperature Regulation Mode | 强制送风循环换热方式+内部冷却系统 Forced air circulation heat transfer mode & internal cooling system | |||||||||
使用环境Operating Environment | 温度:(5~36)℃ 湿度:(30~85)%RH 气压:(86~106)kpa Temperature: (5~36)℃ Humidity: (30~85)%RH Pressure: (86~106) kPa | |||||||||
材料Material | 内箱Inner Chamber | 不锈钢板 SUS304 Stainless steel sheet SS304 | ||||||||
外箱Outer Chamber | 双面镀锌钢板,表面处理后静电喷塑处理 Two-sided galvanved plafe- with electrostatic powder coating | |||||||||
保温Thermal Insulation | 纤维高温棉 High-temperature fiber cotton | |||||||||
箱门密封条 Chamber Door Sealing Strip | 耐高温密封条(不含硅) High temperature resistant sealing strip (exclusive of silicon) | |||||||||
执行器Actuator | 风机Fan | 加长轴风机 Extended shaft fan | ||||||||
风门Damper | 手动调节换气+循环 Manual adjustment for ventilation & circulation | |||||||||
加热器Heater | 进口镍铬合金电发热丝 Imported nickel-chrome electric heater wire | |||||||||
控制器 系统 Controller System | 显示屏+PLCTouch Screen & PLC | 7.0",800×480分辨率,混合输出PLC 7.0", 800×480 resolution, mixed output PLC | ||||||||
运行方式Running Mode | 程式运行(输入的温度和湿度程序运行) Program runs in Auto mode ( An entered temperature & humidity program is run) | |||||||||
设定方式Setting Mode | 简体中文+英文,触摸输入 Simplified Chinese & English, input by touch | |||||||||
显示分辨率Display Resolution | 温度:0.1℃,时间:s Temperature: 0.01℃, pressure: 0.01kPa, time: s | |||||||||
传感器Sensor | PT100(铂电阻) ,K型热电偶 PT100 (platinum resistor),K-type thermocouple | |||||||||
控制方式Control Mode | 抗积分饱和PID+自整定 Anti-integral saturation PID & auto-tuning | |||||||||
通讯功能Communication Function | (选购功能)RS485,方便远程和本地通讯监控,(需配监控软件,RS485/RS232转换器,需用到PC机COM,USB口各1个),同时最多可接16台,线材最长700m (Optional) RS485 makes it convenient for remote and local communication monitoring (monitoring software is required; RS485/RS232 converter, one PC computer COM and one USB port are required). Meanwhile, maximum 16 sets can be connected, the maximum length of wire material is 700m. | |||||||||
附加功能Additional Function | 故障报警提示功能,上下限保护功能 Fault alarm prompt function, upper and lower limit protection function | |||||||||
电源(V)Power Supply(V) | 交流电压380V±38V 频率50Hz±0.5Hz 三相四线+接地保护 AC voltage 380V±38V Frequency 50Hz±0.5Hz 3-phase 4-wire & earthing protection | |||||||||
最大电流(A) Maximum Current (A) | 3 | 4 | 7.6 | 9.8 | 4.1 | 5.8 | 9.8 | 14.5 | ||
电源功率(kW)Power (kW) | 2 | 2.7 | 5 | 6.5 | 2.7 | 3.8 | 6.5 | 9.5 | ||
重量(kg)Weight (kg) | 120 | 160 | 280 | 460 | 120 | 160 | 280 | 460 | ||
标准配置Standard Configuration | 样品架2套,脚轮4个,保险丝4个氧气浓度分析仪1套,流量计3个,减压阀2个,风机变速器1个 2 sets of sample holders, 4 casters, 4 fuses, 1 set of oxygen concentration analyzer, 3 flow meters, 2 pressure relief valve, 1 fan speed transmission | |||||||||
安全装置Safety Device | 漏电开关,电机,相序,超温等保护功能 Leakage switch, motor, phase sequence, over-temperature protection ,etc. | |||||||||
注:氮气进气压力和空气进气压力都为1kgf/cm²。 Note: Both the nitrogen inlet pressure and air inlet pressure are 1kgf/cm². |
● Independent air circulating cooling device.
● Door seal strip with unique thermal insulation function.
● 2 sets of baffles with the maximum loading capacity of 45Kg.
● Self-diagnosis function alarm is used to identify and assist in solving the problem.
● Unique 3-layer chamber structure allows to cool down quickly.
● Unique pneumatic design ensures rapid cooling to reduce concentration and keep low oxygen concentration.
Topect touch-type temperature and humidity controller is specially developed by Topect for the industry of environmental equipment; it consists of touch screen, PLC, temperature module and humidity module, powerful in functions. The touch screen is equipped with visual editing software, PLC logic programme, extensible I&O port and extensible multi-point temperature; USB interface allows users to export data (time optional). Remote monitoring is realized through RS485 communication and PC connection.
●The controllers are developed independently by our company with high performance. Characterized by 65536 color 7’’, TFT true-color touch screen and 800×480 dot matrix, it ensures realistic effects and comfortable operation. In addition, the entire interface is concise and clear, convenient and reliable.
●Our controllers have powerful debugging protection function, fault alarm and troubleshooting description; extensible I&O port can be used to prepare different control programs according to requirement to realize different functions; they can be developed separately according to actual environment but can be controlled by computer intensively through software. The controller interface adopts consistent style, convenient for users’ operation.
●With PLC program control, this system has timed running & stop function and power failure protection function as well as better stability.
●It can be connected to a centralized monitoring software and supports communication protocol, convenient for users’ secondary development; multiple test chambers can be monitored remotely.
●Temperature and oxygen concentration recorder (fig.1)
●Communication interface and software for remote control and data transmission (figure 2)
●Oxygen concentration analyzer (fig.2)
●Metal filter
●Dry filter
●Special load-bearing sample holder
●Circulating fan with speed adjustable
●Non-standard customized equipment can meet users’ demands